Garage Door Controller Tutorial - Step 7 - Your network

Your device is pretty much useless without being on your network. You have at least 3 options to get it on the network. The idea is that you need to connect a networking/patch cable from your device to your network.

Option 1 - If your garage door controller is going to be close enough to your router/switch, you can just use a pre-fabbed Cat5/Cat5e/Cat6 patch cable from the router/switch to your garage door controller.

I don't think this one really needs much explanation. Just tack up your patch cable from the garage door controller to your router/switch, plug it into your router/switch, and call it a day.



Option 2 - Very similar to option 1, except that this way is theoretically cheaper, but requires a little more work.

If you need to run the network cable a longer distance than a patch cable that you can get a hold of, or if you already have some, you can run un-terminated Cat5/Cat5e/Cat6 network cable (cheaper than pre-fabbed patch cables). Then put the end connectors (RJ45s) on the ends yourself.

This is the route I took for my own house...here's a couple photos:

White Ethernet cable tacked to the ceiling of my garage

The other end connected to my network:

Yes, it's a little messy

It's actually not difficult to put the end connectors (RJ45s) on yourself. This Instructable is pretty good and easy to follow. Or, if you prefer a video, this is a pretty good brief tutorial.



Option 3 - If running cable is going to be too difficult/inconvenient, and you have a wireless network already, you can use something like a TP-Link TL-WR702N Wirelss N150 Travel router. You configure it for your network as a 'client' instead of a 'router', then plug a short, inexpensive patch cable from it to your garage door controller, and you're all set.

Just to elaborate on this option a little bit:
If you do want to use a wireless device such as the above, there is a little configuring you need to do. You'll need some information about your wireless network, such as: SSID, MAC address of your existing router/access point, WEP Key Index (if using WEP), and the key/passphrase/password.

As far as how everything fits together physically, here's a photo of a finished installation that I did for one of my sisters:

The TP-LINK device is the blue square device near the top-right of the image above. It has an Ethernet patch cable coming out the bottom (it's the dark gray cable coming out the bottom-left of the device) connecting to the garage door controller. The lighter colored cable coming out the bottom to the right of that is the power cable. So adding this extra little device is actually pretty simple and straight-forward.

Now that that's done, let's go to Step 8 - Mount and connect.

Return to previous - Step 6 - opened/closed sensor (optional).

Garage Door Controller Tutorial - Step 6 - Opened / Closed sensor (optional)

This step is optional, but I highly recommend it. It allows you to know if your garage door is opened or closed. This in itself may be a highly valuable feature - do you ever get the feeling that you forgot to close the garage door when you left your house? Yeah, well, then you want to do this step.

First you need to decide where you're going to install your device, and where you're going to install your reed switch (this will probably be a stationary part of your garage door track or something that will be physically close to your actual garage door). Once you decide this, run your 2 wires from one area to the next, leaving some extra slack (I like to give myself an extra foot or 2). You should 'tack' them to the walls (using the appropriate staples, or wire-ties and screws, or whatever else you like to use), or whatever other surface they're against, so that they stay in place, and are clean-looking.

After the wires are ran, you'll need some way of physically attaching the reed switch and magnet. Here's what I used:

Bracket for the magnet on the left, reed switch in the center, bracket for reed switch on the right

Garage Door Controller Tutorial - Step 5 - Testing

We need to make sure that everything is working before we continue. Remember that IP address that I asked you to remember in Step 3? Well we're going to need that now.

On a computer that is connected to the same network as your garage door controller, get to a command prompt. There are a couple easy ways of doing this:

Method #1 - On your keyboard, press the Windows key and 'r' at the same time. In the window that appears, type in 'cmd' (without the apostrophes), then hit 'Enter' on your keyboard.

Method #2 - Click on your 'Start' button, click 'Programs' (or 'All Programs'), 'Accessories', then 'Command Prompt'.

Whichever method you choose, you'll end up with a black window.Welcome to the 'Command Prompt'. It should look something like this:

Garage Door Controller Tutorial - Step 4 - Putting it together

Now that your Garage Door Controller is all soldered together, and your programmed chip is installed, it's time to combine the main board and the Ethernet Shield.

What I used in place of a proper 'project case' is just a couple pieces of wood (a main platform, and a small strip to hold the Ethernet Shield in place):
(Don't worry about all the holes and marks - I'm using a piece of wood that I've used for other things. Additionally, I've already made the holes for everything for this project)

I don't think it really matters what kind of wood, or what the dimensions are, but the thickness matters for the piece that the Ethernet Shield is going to sit on. You'll see why shortly. That little piece to the right that I'm talking about should be about 5/8" thick:

So go ahead and place your board down on whatever you're going to use, but leave plenty of room to the right of it for the Ethernet Shield:

Garage Door Controller Tutorial - Step 3 - The microcontroller

This section assumes you know the basics of Arduino. If you don't, I referenced a few tutorials/guides in the introduction of this series. But in case you missed them, here they are again:

• Introduction to Arduino (Arduino's website)
• Introduction to Arduino (Instructable...quite long)
• Arduino Tutorial (Ladyada)
• Getting acquainted with Arduino (YouTube video by Jeremy Blum)

First you're going to need the source code (Arduino sketch). You can download it from GitHub here. When you get to my page, click on the 'Download Zip' button:

Garage Door Controller Tutorial - Step 2 - Soldering

Now we get to start the fun part - soldering!

Note that this step is assuming you're using the professional PCB that you purchased from my store. If you want to make your own PCB at home, I have the files @GitHub for a single-sided home-made board available if you want to make your own board. And a separate tutorial for soldering on it.

There are lots of great tutorials on basic soldering, so if you've never soldered, go check some out, then come back here. Here are a few:
Collin's Lab: Soldering - By Collin's Lab / Adafruit Industries
How to Solder Correctly - and Why (Curious Inventor)
Soldering Basics (Sparkfun)


Ready? Ok, here we go...

Garage Door Controller Tutorial - Step 1 - Parts Gathering

Here are the parts:

BOM (Bill of Materials) in relation to above image:

A.	N/A	9V Switching power supply	Part# TOL-00298 @ Sparkfun.com	1	$5.95	$5.95
B.	N/A	Arduino Ethernet Shield	Part# 83-13141 @ MCMElectronics.com	1	$34.99	$34.99
C.	R2,R3	1/4W 10K resistor	Part# CF14JT10K0CT @ Digikey.com	2	$.08	$.16
D.	R1	1/4W 220 OHM resistor	Part# S220QCT @ Digikey.com	1	$.08	$.08
E.	R4	1/4W 1K resistor	Part# CF14JT1K00CT @ Digikey.com	1	$.08	$.08
F.	IC1	28 pin IC Socket	Part# 3M5480 @ Digikey.com	1	$.70	$.70
G.	IC1	ATMega328 w/Arduino Bootloader	Part# DEV-09217 @ Sparkfun.com	1	$5.50	$5.50
H.	U1	5VDC Relay	Part# PB874 @ Digikey	1	$1.61	$1.61
I.	D1	General Purpose 1N4004 Diode	Part# 1N4004FSCT @ Digikey.com	1	$.18	$.18
J.	Y1	Crystal 16MHz	Part# X1103 @ Digikey.com	1	$.81	$.81
K.	C3,C4	22 pF Ceramic Disc Capacitor	Part# 399-4344 @ Digikey.com	2	$.44	$.88
L.	C1,C2	10uF Electrolytic Capacitor	Part# P5161 @ Digikey.com	2	$.20	$.40
M.	Q1	2N2222A Transistor	Part# 497-3108-5 @ Digikey.com	1	$2.76	$2.76
N.	J2	Power Jack 2.1mm x 5.5mm	Part# CP-102A @ Digikey.com	1	$.92	$.92
O.	IC2	Voltage Regulator 5V	Part# 497-1443-5 @ Digikey.com	1	$.55	$.55
P.	LED1	Basic LED (Red)	Part# COM-00533 @ Sparkfun.com	1	$.35	$.35
Q.	X1-X4	Screw Terminals (2 pos.)	Part# ED2580 @ Digikey.com	4	$.42	$1.68
R.	J1	Male breakaway headers	Part# PRT-00116 @ Sparkfun.com	1	$1.50	$1.50
S.	N/A	Magnet Cube (1/4")	Part# COM-08643 @ Sparkfun.com	1	$1.50	$1.50
T.	N/A	Reed Switch	Part# COM-10601 @ Sparkfun.com	1	$1.95	$1.95
U.	N/A	PCB	Part# GDC10PCB @ jamienerd.blogspot.com	1	$5	$5

Total (before tax, S&H, etc.): $67.55

Prices tend to fluctuate a little bit, so don't be surprised if by the time you click those links, the prices aren't the exact same. (They may be a little higher or lower)

Technically, you will need a few extra things (you may already have some on hand), such as:

Wire (to run a couple of wires from your garage door controller to your actual garage door opener)
Electrical tape
Krazy Glue
Brackets and screws (to mount to your garage door for the reed switch and magnet)
Some Cat5/5e/6 network cable

And of course there are a few basic tools you're going to need:
Knife (or wire stripping/cutting tool)
Soldering iron
Solder
Small screwdriver

The 2 lists above are only a couple of general lists - what you will really need depends on the way you go about your project - you may need more or less tools/supplies.

You'll also need a way to program your microcontroller - an actual Arduino board would be an easy way.

If you want to save a little money, you could skip the screw terminals (Q). This would mean though that you would have to solder wires onto the PCB instead of having the convenience of having 'removable' wires. You could also technically skip the magnet cube (S), and reed switch (T) which is the 'sensor' that can tell you if your garage door is open or not. If you decide to skip those, the Android app would always show your garage door as 'open'. You should probably only skip this if you have another way of knowing the status of your garage door (camera, etc.).

I know this isn't the cheapest project, but to me, it's worth the awesomeness of being able to open/close your garage door with your Android cell phone/tablet! If you want some tips on how you can save yourself a little money, please check out my FAQ, under the 'Is there anything I can do to bring the total cost of the project down?' question. 

On the other hand, if you want to spend a little less time (but a bit more money), I have a few options in my store, including full assembled board, or a full kit, etc.

Once you have all your parts, let's continue to Step 2 - Soldering.

Return to previous - introduction.

Garage Door Controller Tutorial - Introduction

I call this project 'Garage Door Controller'. The hardware is based on Arduino, and the 'software client' is an Android app. I do not have any immediate plans to release an iOS version of the software as I have no interest in developing on that platform (I'm not a fan of Apple's closed source model). However, if there is someone out there interested in porting the program to iOS, you may contact me and we can discuss that.

With the hardware and the free Android app, you will be able to see if your garage door is opened or closed, and you will actually be able to open and close it...from anywhere in the world you have Internet access.

Before you go any further, let me just make a couple things clear:

1. You need to have a working automatic garage door opener
2. I'm assuming you have the ability to run an Ethernet cable from your network switch/router to your garage door controller device, which should be near the general vicinity of your automatic garage door opener. (Technically you don't have to run an Ethernet cable to your router/switch...if you have a wireless router and/or Access Point, you could use one of these. I explain this more in Step 6.)
3. I'm assuming you have the ability to run (2) lengths of wire (light gauge/low voltage) from your garage door controller device to the vicinity of your garage door. This is your 'sensor' that will tell you if your garage door is open or not. (This is not required, but recommended)
4. I'm assuming you have a way of programming an ATMega328 microcontroller. For example, you have a computer running Windows/Mac/Linux (to run the free Arduino IDE), a standard USB cable, and an Arduino board (or similar/compatible). If you are brand new to Arduino, you should check out some of the following links:

• Introduction to Arduino (Arduino's website)
• Introduction to Arduino (Instructable...quite long)
• Arduino Tutorial (Ladyada)
• Getting acquainted with Arduino (YouTube video by Jeremy Blum)

All the source code for the Arduino and the Android app are linked below. The Android app is called 'Garage Door Controller' and is available for free on Google Play.

There is a possibility that you may run into a slight inconvenience when using this system if your router does not support loopback. Please check out my post, Garage Door Controller Tutorial - Using the app away from home for more info on this.

The project cost can vary wildly, so a very rough estimate would be around $40 - $85. It depends on several factors. Please see my FAQs page under the question, 'Is there anything I can do to bring the total cost of the project down?'. Obviously the more components you already have on hand, the cheaper it will be (it may actually only cost you a few dollars!).

How does this device work? You connect your garage door controller to the Internet by connecting it to your network. Connect the garage door controller to your automatic garage door opener. Install a reed switch and magnet on your actual garage door, and the (2) wires that come off of that connect to your garage door controller. Download and install my free Android app to connect to the garage door controller over your network and/or over the Internet to check the status of the door, and open and close it.

Here is a video of my device in action:

Downloads/links for this project (all on GitHub):

1. The Arduino sketch (and supporting files)
2. Android app source code
3. Circuit board files (for submitting to professional board house)
4. Circuit board files (for making your own circuit board at home)

I tried to break this project down into several smaller steps:

1. Step 1 - Parts Gathering
2. Step 2 - Soldering
3. Step 3 - The microcontroller
4. Step 4 - Putting it together
5. Step 5 - Testing
6. Step 6 - Opened / Closed sensor (optional)
7. Step 7 - Your network
8. Step 8 - Mount and connect
9. Step 9 - Smartphone app
10. Using the app away from home (supplemental/optional)

In the next step, I provide direct links (to Digikey, Sparkfun, etc.) to the individual parts you'll need. As an alternative, you can check out my store which includes the full kit, fully assembled device, etc which may be more convenient for you.

Ready? Let's go - Step 1 - Parts Gathering!

Disclaimers:

1. I am not responsible for any damage/harm you may do to your garage door, your phone, yourself, or anything/anyone else during this project.

2. I am not a professional electronics engineer, or a professional programmer. I have had no prior Android development experience, so I picked up a couple of books and started learning for this project. In other words, please don't laugh at my code. On the other side of the coin, I would love to hear ideas/suggestions from the more experienced programmers out there.
3. Even though I've implemented a 'password' requirement for the Android to be able to send commands to the Arduino to open the garage door, it's not very strong security. It's sent as plain text over the internet, so anyone with the right software and know-how could intercept it, and start opening/closing your garage door with just a little more info. I do have some ideas about implementing better security, so in future Android/Arduino releases I may implement something...but can't make any promises.

Nerd verification - A+ Certification

This is just a quick post to prove my 'nerdness'. I recently became A+ certified. What does that mean? Well, let me just quote from CompTIA's website regarding just that:

"In order to receive the CompTIA A+ certification, you must pass two exams.

CompTIA A+ 220-801 covers the fundamentals of computer technology, installation and configuration of PCs, laptops and related hardware, and basic networking.

CompTIA A+ 220-802 covers the skills required to install and configure PC operating systems, as well as configuring common features (e.g. network connectivity and email) for mobile operating systems Android and Apple iOS."

Soooo, does this make me a certifiable nerd? Idk (I don't know).

What, you want proof that I'm certified? Ok, well you can verify here. My code is:
7C8ME3Z10341SD5N.

Finally, here's a copy of my certificate:

Philips Norelco shaver guts

Ever want to know what the electronics looks like in a Philips Norelco shaver? Ok, so I'm pretty sure not many people care, but I did (and I had a reason). I have been using one of the cheaper models (purchased from WalMart for about $40) for about 2 years now and it finally pretty much died on me the other day.

I won't go into much detail, but because I was interested in salvaging the motor, I tore the thing apart until I got to the bare electronics. Here's what it looks like:

If you're not sure what these look like before they're massacred, here's a photo of the one I bought to replace it, which is pretty much what the old one looks like, just a little more modern looking:

What's that? Why did I want the motor you ask? Well stay tuned...